150吨立式液压打包机
配用动力：15KW，
台时产量：3-5个包块，
包重：200-800KG，
油缸：Φ160*2支，
150吨立式双缸设计
型号：150
公称压力主缸KN：1500
液体*大工作压力MPa:18
料箱尺寸长1100mm,宽700mm,高:1400mm
包块尺寸:长1100mm*宽:700 *高:(1000）mm
包块密度kg/m3：≥1000
单次循环时间S：45
电机功率KW：15
油缸行程：1200MM
机器外形尺寸mm：长1700*宽1400*高3900。
整机重量kg；5500.
150吨液压打包机使用说明：
本厂150吨液压打包机使用68#液压油，连接电源三相380V，额定电流为25A，安装时要有接地保护，电机要根据所示方向运转才能启用，否则不能启动。油箱加入120公斤的液压油方可启动使用。但当气温降低时液压油浓度大，机内的滤清器不能起到过滤作用，这时必须将滤清器拆出，待温度恢复后，方可生新安装使用。（注：滤清器应每月清洗1-2次）。
溢流筏-控制该机的压力开关,旋转调压手转向右转为增压，向左转为减压，出厂前已调整好压力。但在使用过程中调压手轮可能有变位现象，导致压力升高或降低，这时需要生新调节压力，调压时应在运转中进行，同时把压板降至*低位置，调整溢流筏的调压手轮，调整压力不能高于或低于压力表所示的范围，*佳压力的OMPA（100KG/1cm2）。旁杆-增强压的刚性和起导向作用，每次使用前应加油，起润滑作用。
行程开关-控制该机的启动和停止的作用，因此要经常检查、维修、保养。手动转向阀-控制压板向上向下，停止的开关。
1、手动转向阀打向下档位时压板自动向下工作，当废纸压到结实状态时，那阻力大于压力：压板不能再向下压，应把手动转向阀打向空档位置，停止加压，如果长期处于加压状态，会导致液压，电机、油泵长时间处于超负荷状态而使各机件损坏。
2、手动转向阀打向升档位置，压板自动向上升到*高的位置，由行程开关控制自停，这时应把手动转向空档位置。完成一个工作程序。
液压打包机使用说明书：
一、150吨液压打包机安装步骤
1、本机必须平稳放在混凝土上，基础视当地情况决定。
2、检查油箱底部放油口是否已关闭，确定关闭后再打开油箱顶部加油口密封盖。
注入约90KG,68#液压油，液压油排号视当地气温及使用标准决定。[注！如果机型在60T以上，新机时必须分两次注油，**次注入液压油高度至油尺顶部（蓝**线）。待压板下压至底部再加注液压油至油尺底部（红**线）详细见操作说明4]
3、安装好本机电源线,电压及频率视当地电源决定，（注！电机和电器配件的电压及频率已按客户订购机器时的要求配置安装好）常规采用三相四线制，其中三条带电源线分别接入电相内相应的三个接线位，（图7左）另一条为接地防漏电保护线，应紧接机体外露金属表面，以防电器漏电伤人。
二、150吨液压打包机操作方法：
1、通入电源：把电箱内空气开关（本机总开关）合上，先检查三相电源电压是否正常，（用仪表或探电笔测试）关闭电相门，查看电相门板表面红色电源指示灯是否亮起。
2、启动电机：把手动换向阀手柄（付图3）往下推至*底位（机体附有操作图标），然后把启动按钮NO按下（图5右下），（注：如装有急停开关机型的请把急停开关按箭头方向右旋，急停开关弹出即可），（图5右上）如正常情况下电机启动。
3、 检看电机转向：（图8）电机启动后，手动换向阀手柄在*下位时，如压板不能往下移。这时请必须立即查看电机旋转方向是否正确，电机旋转方向必须按箭头指示方向一致。如果电机转向相反时则机器不能正常使用，这时应把手动换向阀手柄往上拉至中档位。然后按下停止按钮OFF（或急停开关按下）停止电机运转。切断输入总电源，把三相电源线其中二相线互换再接上即可。再按操作1和2重新操作，（注！必须确定电机转向是否与箭头指示方向一致。）
4、注入油量的关健：当压板正常往下移时，压板在**次移动，移动速度是不均匀的。待压板移至底部或移动中突然停止又或移动中噪声加大，这种情况下应先把手动换向阀手柄往上拉至中位，把停止开关OFF或急停开关按下，停止电机运行。再仔细查看油箱储油量是否足够，如油量底于油箱高度一半时，证明油量不足，这时应再次往油箱注入适当液压油。这次加油量应加至油位尺*底界线（红**线）即可。150吨液压打包机操作方便， 接上电源后打包 , 专用于一切轻泡、松散物料的打包。可应用于棉、羊毛、废纸、废纸箱、废纸板、纱线、塑料、布匹、编织袋、针织绒、麻、麻袋、毛条、毛球、茧、蚕丝、啤酒花、麦柴、草、废塑料袋等一切轻泡、松散物料。包型紧凑，整齐美观，可大幅降低运输成本，是棉产区、纺织企业、超市、服装厂、废旧物资回收业和其他各种轻工业企业的生产工具 。
150 tons of vertical hydraulic balers
Scrap balers,
Equipped with power: 15KW,
Taiwan when the output: 3-5 mass,
Package weight: 200-800KG,
Cylinder: Φ160 * 2,
Easy to operate,
Connected to the power after packaging, dedicated to all light foam, loose material packaging. It can be used in cotton, wool, waste paper, waste paper box, waste paperboard, yarn, plastic, cloth, woven bag, knitted cashmere, hemp, sack, top, hair ball, cocoon, silk, hops, , Waste plastic bags and all the light foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises.
150 tons of double cylinder hydraulic balers
Model: 150
Nominal pressure master cylinder KN: 1500
Liquid maximum working pressure MPa: 18
Box size 1100mm long, width 700mm, height: 1400mm
Bulk size: Length 1100mm * Width: 700 * Height: (1000) mm
Mass density kg / m3: ≥ 1000
Single cycle time S: 45
Motor power KW: 15
Cylinder travel: 1200MM
Machine dimensions mm: length 1700 * wide 1400 * high 3900.
Machine weight kg; 5500.
Instructions for use:
The factory is equipped with 68 # hydraulic oil, connected to the power supply three-phase 380V, rated current of 25A, the installation should be ground protection, the motor should be operated in accordance with the direction shown to be activated, or can not start. The tank to join the 150 kg of hydraulic oil can be used to start. But when the temperature drops when the hydraulic oil concentration, the machine can not play a filter filter, then the filter must be removed until the temperature is restored before the new installation and use. (Note: the filter should be cleaned 1-2 times per month).
Overflow raft - control the machine's pressure switch, rotary pressure hａnd turn right to pressurized, turn left to decompression, the factory has been adjusted before the pressure. But in the course of the use of pressure handwheel may have a displacement phenomenon, resulting in increased or decreased pressure, then need to add a new regulation of pressure, pressure should be carried out in the operation, while the pressure plate to the lowest position, adjust the overflow Rafts of the pressure regulating handwheel, the adjustment pressure can not be higher or lower than the pressure gauge shown in the range of optimum pressure for OMPA (100KG / 1cm2). Side bar - to enhance the rigidity of the pressure and play a role, each should be used before the fuel, from the lubrication.
Stroke switch - to control the machine's start and stop the role, so often check, repair, maintenance. Manual steering valve - control the pressure plate up and down, stop the switch.
1, manual steering valve to play down when the pressure plate automatically down work, when the waste paper to a strong state, that resistance is greater than the pressure: the pressure plate can not be pressed down, the manual steering valve should be turned to neutral position, stop Pressurized, if the long-term pressure state, will lead to hydraulic, motor, pump for a long time in a state of overload and damage to the parts.
2, manual steering valve to the upshift position, the platen automatically rose to the highest position, controlled by the trip switch from the stop, then the manual should be turned to the neutral position. Complete a working procedure.
Hydraulic baler instructions:
First, the installation steps
1, the machine must be placed on the concrete, the basic depending on the local situation.
2, check the bottom of the fuel tank is closed, to determine the closure and then open the top of the tank filling port seal.
Injection of about 90KG, 68 # hydraulic oil, hydraulic oil row number as the local temperature and the use of standards. [Note! If the model is above 60T, the new machine must be filled with oil twice, the first time into the hydraulic oil height to the top of the dipstick (blue line). Press the press down to the bottom and then add the hydraulic oil to the bottom of the dipstick (red border) see the operating instructions in detail 4]
3, the installation of the local power cord, voltage and frequency depending on the local power supply decision, (Note! Motor and electrical parts of the voltage and frequency of customer orders have been ordered to install the machine installed) conventional three-phase four-wire system, three With the power cord, respectively, into the electrical phase of the corresponding three wiring bits (Figure 7 left) and the other for the ground leakage protection line, should be exposed to the body exposed metal surface to prevent electrical leakage wounding.
Second, the operation method:
1, access to power: the air box inside the air switch (the main switch) to close, first check the three-phase power supply voltage is normal, (with a meter or probe pen test) to close the electrical phase door, see the power of the door surface red power Whether the indicator light is on.
2, start the motor: the manual valve handle (pay Figure 3) down to the bottom (the body with the operation icon), and then press the button NO button (Figure 5 lower right), (Note: if installed There are emergency stop switch models, please put the emergency stop switch in the direction of the arrow, the emergency stop switch can pop up), (Figure 5 on the right) as normal under the motor start.
3, check the motor steering: (Figure 8) After the motor starts, manual valve handle in the lowest position, such as the pressure plate can not move down. In this case, you must immediately check whether the direction of rotation of the motor is correct and the direction of rotation of the motor must be in the direction indicated by the arrow. If the motor turns to the opposite when the machine can not be used normally, then the manual valve handle should be pulled up to the mid-range position. Then press the stop button OFF (or the emergency stop switch is pressed) to stop the motor from running. Cut off the total input power, the three-phase power cord which can be connected to the two-phase line. And then press operations 1 and 2 to re-operate, (Note! Must determine whether the motor steering direction is consistent with the arrow.)
4, into the fuel of the key: When the pressure plate down the normal move, the pressure plate in the first move, the movement speed is not uniform. To be pressed to move to the bottom or move suddenly stop or move the noise increases, in which case the manual valve should be pulled up to the middle of the handle, stop the switch OFF or emergency stop switch, stop the motor run. And then carefully check the tank oil storage is sufficient, such as oil at the end of the fuel tank height of half, to prove that the amount of oil, then again should be injected into the tank appropriate hydraulic oil. The amount of fuel should be added to the bottom line of the oil level (red line) can be.
深圳市达安泰机械设备有限公司是注塑成型周边机械*生产厂家。随着人们对塑胶产品的要求越来越高，注塑工艺日益*。因此，公司不仅注重产品品质，更致力于研究开发高效、节能、环保之优质产品、以感谢广大新老客户的支持与厚爱。
凭借十多年的技术革新优势和工程技术人员的不断探索，为产品的更新换代，精益求精，奠定了坚实的基础。在所有产品的设计和制造上都体现了客户的宝贵意见及市场的适用性，力求尽善尽美；在主要部件方
达安泰人，用心、专心、诚心！
质量方针：品质*；服务*；精益求精；顾客满意。
经营理念：以质量求生存；以创新求发展；
以服务树信誉；以品质塑品牌。
我们的宣言：
1） 协同*：人心齐，泰山移。成则举杯相庆，危则拼死相救。
2） 说和做：能说能做，说到就要做到，说到不如做到。做就要做好。成王败寇，能者上；结果先导，过程为辅。
3） 建设性的对抗：指快速处理问题，要把问题拿到桌面上来讨论，允许各抒己见，寻求解决问题的*策略，鼓励员工尽快地发现工作中的问题，不管是否由你负责，也要乐于参加争论并寻求解决问题的办法。无法得到结果时，实战解决和证明。
4） 创新和风险：在主次、轻重、缓急清晰明确的前提下，寻求一切可以创新的领域和机会；在可承受的前提下，全力以赴地为跳跃性的发展和成长机会迎接挑战和机会。总体上呈现为波浪式推进，把握机会上台阶，不轻易冒进，也不轻易逃跑。
5） 沟通：我们重视沟通、认为无论外部还是内部、经营还是管理等各个环节，倾听和双向交流成为必要；
6） 学习：在所有时间和空间的坐标上，决定谁被淘汰和谁将获胜。
7） 声誉：我们相信任何历史将被记录并对现实和未来形成重大影响。企业、团队、个人概莫能外。
8） 客户：通过以交换方式，来达到满足特定需求，Z终影响他们行为的人。客户并非简单*，客户的发展才是*。客户满意定义:超过期望,惊喜,喜出望外。精诚合作、*结盟。以客户为中心，和客户共同创造未来。
9） 市场：所有交易关系和交易过程和结果的总和；通过沟通达到满足要求的过程。要求大胆构思，审慎求证，坚决实施；实事求是的自然之道（尊重客观规律和人性）。
10） 资源：创造和利用有形资源（厂商、政府相关政策和产业环境等，办公环境及设备，宣传手册等）；开发、挖掘、利用、分享无形资源（客户，市场、品牌等）。资源如水，要有活水，要有组合，要有边缘效应，要有能够叠加出乘法效果，甚至几何效果、指数效果。
11） 质量：寻求相匹配的，但超过竞争对手的品牌。从拜访客户到接听电话，从设计方案到售后服务，每一个环节都凝结我们的心血、气质和风格。
12） 价值：能被营销环节（客户，厂商，股东，员工）认可的事情。
13） 利润：有形和无形的资产净值的增加，是企业和企业员工的价值体现。没有利润对个体而言，是浪费生命；对企业而言，是浪费资源。
14） 供应商、厂商、 合作伙伴：眼光、方法和成本的重要来源。追求相互“尊重、信任、发展”圆满和谐之境界。
模温机,油温机,注塑料模温机,水冷式冷水机,风冷式冷水机。开放式冷水机,螺杆式冷水机，料斗干燥机，热风干燥机，塑料干燥机，塑料除湿机，除湿干燥机，冷却塔，冷水塔，卧式混合机，立式混合机，塑料混合机，滚筒式混合机，干粉混合机，高速搅拌机，立式搅拌机，螺旋搅拌机，干粉搅拌机，粉末混合机，拌料机，混色机，混料机，塑料破碎机，塑料粉碎机，再生塑料破碎机，再生塑料粉碎机，强力粉碎机，塑胶破碎机，吸料机，抽料机，自动吸料机，顶吸式吸料机，感应式吸料机，电眼式吸料机，小型吸料机，300G吸料机，700G吸料机，800G吸料机，880G吸料机，大型吸料机，塑料振动筛，振动筛粉机，振动筛料机，机边粉碎机，机边回收机,模具架，抽屉式模具架，重型模具架，中央供料系统，冷却塔安装
150吨液压打包机
产品信息
